Atwood Furnace Ignition Lockout Fault

If your furnace is locked out it will most likely remain in that state until its reset. I changed the control board because that seems to be a common fix and its pretty easy just not on the wallet.

Atwood 8535 Furnace Wiring Diagram For Rv 120 208 Single Phase Wiring Diagram For Wiring Diagram Schematics

Maybe a bad ground.

Atwood furnace ignition lockout fault. Tries two more times then stops with a fault code of 3 red flashes then a pause. My Atwood 7920-ii furnace tries to light I hear clicking of the spark igniter but it ultimately fails and goes to ignition lockout fault three blinks on the red light followed by 3 second pause. They heat the vehicles.

Common causes of furnace lock outs are a defective igniter or defective flame sensor. When a sensor detects an unsafe condition the furnace controller will shut off the power and fuel to prevent hazards. Atwood 8516 Technical Lnstallation Manual.

Check the RV system voltage. The flame lights on each attempt but after two seconds it goes out. MalfunctionDefective Control Circuit Board After you are certain that the battery is not at fault the next thing to check is the control circuit board of the Atwood furnace.

When the furnace attempts to start sensors check for igniter action and for the presence of flame. If the igniter doesnt activate within a few seconds the furnace controller stops the ignition sequence. This will lead the temperature limiting switch to turn off the furnace.

_____ 2008 Jayco Jay Feather Sport Ultra Lite 197 2005 Dodge Durango V8. Any obstruction in the vents will result in malfunctioning and heating of the furnace. Fan will start can hear burner ignite can hear igniter still clicking after it fires then burner stops and fan keeps running.

They come in a variety of sizes for different recreational vehicle needs. The Furnace may be in lockout. At the end of the three attempts I get a lamp flashing 3 times indicating an Ignition Lockout Fault.

Luckily for me I remedied the problem before needing a furnace tech to look at it. After that the LED on the board blinks 3 times indicating Ignition Lockout Fault. In fact most annual furnace inspections involve a technician cleaning the flame sensor as part of the preventative service visit.

The 12 VDC power is low. That would mean that the electronics is not detecting a flame that MAY be there. Ignition lockout fault atwood furnace.

Internal Circuit Board fault Steady on no flashing Limit switchAirflow problems 1 flash with 3-second pause Flame Sense fault 2 flashes with 3-second pause Ignition Lockout Fault 3 flashes with 3-second pause So it appears you have an ignition lockout fault. Atwood 8940-iii-DCLP LD furnace problem. This is known as an ignition lockout a condition that can be caused by a number of different sensors found in your furnace.

2334 2334-LD 8520-LD 8525 8535. Troubleshooting the RV Furnace. The flame sensor comes into contact with the flame and it is quite common for debris to buildup on it.

Three blinks was an ignition lockout fault. Reset the Furnace by switching the thermostat to OFF for 10 seconds then switch the thermostat to ON. Ignition Lockout Fault----------------3 flashes with 3-second pause You are having an ignition lockout fault.

Another common problem that can cause a furnace lockout is a dirty flame sensor. Atwood furnaces offer two-stage heating digital thermostats and self-diagnostics. Unfortunately that didnt do it.

This is part 1 in a sears of videos for the operation diagnosis and repair of an Atwood furnace. I didnt get it to work till I got home. I have reset the furnace have plenty of propane slowly turned off and back on the propane to see if the regulator read more.

My Atwood furnace is not lighting and giving me the ignition lockout fault signal. Check for the furnace box see if there is anything that is blocking the furnace vents. Time delay relay Used on older furnaces newer furnaces have the relay incorporated into the circuit board This relay performs two separate jobs - one to handle the relatively high current needed to run the blower motor - and two to allow the blower to run for 45 to 90 seconds after the thermostat is satisfied.

This version of Atwood 1522 Manual compatible with such list of devices as. After three or four start ups from scratch the furnace will finally stop failing and then runs perfectly for days on end without further failure. I have good gas flow and its clear that the gas is igniting as I get hot exhaust.

This can be caused if the furnace vents are blocked. In the case the board is falling the operation of the gas valve and the igniter would be severely disrupted. Atwood furnaces are designed primarily for use in recreational vehicles such as motor homes and travel trailers.

That would mean that the electronics is not detecting a flame that MAY be there. The Furnace-installed breaker switch may be tripped or OFF - Contact a trained RV service provider.

Hydro Flame Atwood Furnace Repair 8531 Ii Youtube